it's okay, there are folks(out there,... somewhere... I'm sure ..) who have never thought about the insides of their machines, or don't know that all mechanical machines can still exist without some kind of circuitry..
KM (novice Luddite)
it's okay, there are folks(out there,... somewhere... I'm sure ..) who have never thought about the insides of their machines, or don't know that all mechanical machines can still exist without some kind of circuitry..
KM (novice Luddite)
I think that is likely to be an excellent resource. No controversy that I can see. What always concerns me is the guy (not to be sexist) who has no clue and watches something that gives him enough information to be dangerous. He then decides to save a few bucks and take care of the wife's top of the line Janome at home. Spritz, spritz.. twist, twist with a magnetized screwdriver... snap crackle pop... "But they said on YouTube......." Electronic and computerized machines are a whole different ballgame.
For a straight out mechanical machine it looks good and helpful. But those are becoming harder and harder to get. Just a caution to those who need it. I'm not saying "Don't clean the inside of the machine." I'm saying do it right. If you blow dust and grit farther down into an electronic machine you stand more chance of damaging something. If you exhaust all that stuff and get it out of the way, IMO, you are much better off.
I may be slow... But I sure am gimpy.
"Bless you child, when you set out to thread a needle don't hold the thread still and fetch the needle up to it; hold the needle still and poke the thread at it; that's the way a woman most always does, but a man always does t'other way."
Mrs. Loftus to Huck Finn
We Don't Sew... We Make Gear! video series
Important thread injector guidelines especially for Newbies
Bobbin Tension - A Personal Viewpoint
"...a light blast," Rev!
Always consider moderation... especially here at HF!
- MacEntyre
"We must, indeed, all hang together or, most assuredly, we shall all hang separately." - Ben Franklin
www.MollyMacGear.com
First off...thanks for the great advice. We're not sure exactly what happened to the machine but were told the needed part is no longer being manufactured. I had considered trying to find the part elswhere but am not sure where to even look. Would that be a possibility and if so where would I look?
And you're right....she's far closer to being a seamstress than a gear maker.
Miguel
You could try ebay and craigs list for the same or similar machine, but beware. If your bad part is that way because of use, other machines may very well be on the fritz for the same part.
If on the other hand you dropped it and broke the Gleinhemstop, well, then another machine may be your best bet.
Off topic, but have you seen the reproduction machines that Jay Leno used to make a valve for one of his steamers? Put the part in front of a 3D scanner, the tech did some photoshopping of the final 3D piece and a plastic printer makes a replica right before your eyes. A little lost mold casting later and Jay's steamer was back in place. Shouldn't be too long before you're part can be reproduced as a one off.
This should definitely be a sticky. Thanks for the great information!
GoodWill, Salvation Army and other Thrift Shops carry Thread injectors. I found a machine that works very nicely on heavy stuff. Has a few basic stitches built in (no pain in the rear Cams), everything seems to work great, sews silnylon just like it sews cotton. I am very pleased All for under $25.00. The trick is I looked at a lot of rejects before I found a keeper, and my keeper happens to be FOR the Japanese Market.
My expensive Thread Injector, is fussy about what it will sew, the timing gets off, and there are a lot of little things it is touchy about. A lot like my Jag, the machine needs alot of extra care. Not like the old VW, just get in and drive.
I am coming to this post way late, but the reason for not using an air compressor for cleaning electronics is that it can create static (the friction of air molecules or some such thing) "canned air" has been "neutralized" some how. I know the engineers on here could explain it if we realy cared. Modern Computerized sewing machines are closer to a desktop computer than a treadle machine.
It seems I have read warnings about using canned air on computers as well. Flying dust and particles can short out circuit boards faster than you can sneeze. The pre-circuit board machines can pick up dust and lint which hardens over time and needs professional cleaning. I just think it is a risky idea. But that's my opinion.
I may be slow... But I sure am gimpy.
"Bless you child, when you set out to thread a needle don't hold the thread still and fetch the needle up to it; hold the needle still and poke the thread at it; that's the way a woman most always does, but a man always does t'other way."
Mrs. Loftus to Huck Finn
We Don't Sew... We Make Gear! video series
Important thread injector guidelines especially for Newbies
Bobbin Tension - A Personal Viewpoint
I tend to agree with you on the canned air. But according to theory it is supposed to be "safe" for electronics. I have personally seen a board fried from being blown out with an air compressor. A quick spark some minor smoke and a dead computer. I never blew air of any kind into electronics after that.
Bookmarks