“The nitrogen in our DNA, the calcium in our teeth, the iron in our blood, the carbon in our apple pies were made in the interiors of collapsing stars. We are made of starstuff.”
Have you checked the timing on it yet? The 201's have a rotary shuttle versus an oscillating one. Make sure there are no burrs on the hook and that it is smooth wherever the thread will touch it. Might also be a good idea to take the upper thread tension mechanism totally apart and clean and inspect it. Take pictures at each step as you go along in the dismantling process and refer to them when it comes time to reassemble. Wouldn't worry too much at putting lipstick on the pig so long as the pig works as designed.
I have no plans to place a stitch with this till all is done with my motor overhaul (brushes, wicks, inspect and likely wire replacement) -
Bob in case is horribly dirty so gonna get it taken out and all that spiffy
I have no idea how to check timing yet?
I have no plans to make it look super pretty besides being clean and I’ll do some policing on the plates and likely some acrylic pain on the slitch length plate thingie
Already watched a video showing the thread tension mechanism - plan to take it all apart and clean then put back on - inspect the spring make sure it seems good (externally it seems fine.
Sent from my iPhone using Tapatalk
“The nitrogen in our DNA, the calcium in our teeth, the iron in our blood, the carbon in our apple pies were made in the interiors of collapsing stars. We are made of starstuff.”
As a bonus, doing all this should give you a greater understanding of the mechanics of the machine.
You need this (download and save it)... https://imagespast.files.wordpress.c...ers-manual.pdf
If you don't have the user's manual, that can be found online as well.
From my experience, the "timing is rarely off".
There is normally no need to disassemble any of the internal shafts, gears, etc. as all of the oiling points are accessible from the outside and below.
Dad was a collector and had hundreds of machines at one time. I have about 20 including 201's and 15-91's with potted motors.
FLScouthanger is spot on about insuring the hook is smooth with no burrs from needle strikes. Check the hole in the needle plate for burrs as well.
Don't use the currently sold Singer grease for the grease pots/wicks as the melting point is now too high and it will not wick properly. Use Petroleum Jelly...https://archaicarcane.com/a-search-f...e-replacement/
Last edited by gmcttr; 11-17-2017 at 17:28.
It does happen. I have 8 machines (I'm a lightweight compared to some on this forum) that I've picked up various places. It's fun to bring them back to life. The last one was when my wife and I were walking through a goodwill outlet looking for mid-century modern furnishings and she sees a Singer 401a in a bin for $15. I already have a 401a, but how do you pass it up for $15? It felt like they were teasing me a little. The urge has kind of died down now as I'm only watching for a Kenmore with the larger 1.2 amp motor or a treadle machine.
Bill
I’m making good progress - have to wait for my proper screw drivers to remove the worm - then I’ll see inside the motor and the state of the wires
The wicks were as hard as a brick - I have new wicks ordered - gonna clean up the bobbin case good tonight
Sent from my iPhone using Tapatalk
“The nitrogen in our DNA, the calcium in our teeth, the iron in our blood, the carbon in our apple pies were made in the interiors of collapsing stars. We are made of starstuff.”
What do you think of this stuff? I have been using it with success. https://www.novamontgomery.com/shop/...t-x4312153.htm
“The nitrogen in our DNA, the calcium in our teeth, the iron in our blood, the carbon in our apple pies were made in the interiors of collapsing stars. We are made of starstuff.”
Bookmarks