Wow! Nice hammock! Very clean workmanship
I'd pay to stand behind you and look over your shoulder.
Some national parks have long waiting lists for camping reservations. When you have to wait a year to sleep next to a tree, something is wrong. ~George Carlin
Sweet set up. Thanks for posting pics
Wouldn't a cat cut on the ends make the sides slightly longer in relation to the center compared to a straight end? My sewing machine slightly puckers my fabric on the end channels. That made the sides tight when I sit down In the hammock making me reluctant to sit in the hammock with my lower legs hanging over the edge for fear of ripping my end channel stitches with the sides so tight. So I was thinking about putting a 2-3" cat cut in the ends to counter the tight sides I got on my first hammock. How do you like yours so far?
The theory in hammocks is not simple because there are many factors. Any minor changes you make have an impact. In the picture below I have tried to illustrate ½ a hammock but please have in mind is in 2D and hammocks are in 3D. When you add the ridgeline/sag you get the third dimension.
I won’t pretend I understand it all because I don’t.
We start out with flat piece of fabric and then we gather it and if you look at ¼ of the hammock it becomes a triangle but because the outer edge is shorter it adds sag and tighten the edges.
Adding a cat curve to the ends (it’s actually called a convex because its “out going”) the center of the hammock drops down/the edges get shorter and tighter. The result is a deeper hammock.
If you add a concave shape (inwards curve) to the long side edges the sides are lowered but hammocks bottom shape will remain the same. What you gain is less floppy edges in the middle and its more easy to get in and out of but less side support. Depending on the depth of the concave shape you will also remove some of the “side wall” in the head and foot end and then your feet and head can move over the edge if you don’t have an integrated bugnet. BTW checkout XTrekker’s bugnet video, very cool!
A while back I made a hammock with approx 3” convex ends and 6” concave side edges. I won’t do that again! It’s too deep and very unconvertible to sit in. If you use a rolled hem on the edges it won’t rip. Mine did not, HyperD 1.6 and 1 stitch row.
Something to remember is if your hammock ends are symmetrical (alike) any changes you make has a x2 factor.
The method used for gathering the ends also changes the hammock shape. XTrekker’s ends are closed and pulled towards the center with a zip-ty. It gives a very nice finish if you ask me. If it was hung from a sewn channel the hammock would be a little bit deeper.
Sewing a hem or channels on a curve is a nightmare and the smaller it gets the worse it is. The reason is our thread injectors are made for sewing in a straight line and it feeds the fabric in a straight line under the pressure foot. For hems I use a tool I made also for big cat curves but it is a challenge and the result is not perfect but for smaller cat curves pins are the only solution if you can’t do it free handed. Sometimes it helps to start at the middle and sew towards the edge, especially if you are sewing a wider channel (>1/2”).
Anything you do has pros and or cons!
shape.jpg ang.jpg
Thanks for the good explanation Snowball.
Sorry its been a bit since I have had a chance to visit this thread. In response to the catcuts that I put on my hammock ends;
I usually do them with a shallow curve. Usually only about 1.5" curve on each end. This adds up to be about 3" difference between the lengths of the sides and the center. To be honest, I really dont cut an actual cat curve. I have found that the perfect balance is with a 10"-12" section in the center of the ends where there is no cut. And I typically do straight cuts to make things easier to stitch. This method was really never meant to give the hammock a different lay but rather alleviate some of the side flop of the hammock. This is really a preference thing and others may not find the results as desirable.
Untitled-1.jpg
I know now it wasn’t your intension to change the lay with the end shapes but now I am curious. Do you know if the lay changes with your semi straight ends VS. a convex end?
I have tried many combinations but never your shape but it makes sense because an arch is a pain ……. to sew.
In my experience it doesn’t take more than ½-1” in the ends deliberately, odd shapes or unintentionally before it makes a difference in the lay. These days I prefer to hang from a channel end its because of the lay. Visually I like your method better but comfort has priority for me.
BTW thanks for the videos! Much appreciated
Bookmarks